The Lifting Method of Industrial Lifting Doors (Lift Slide Door)
If the installation surface is a brick concrete structure wall, it is required that the wall surface be flat and firm. When installing other supporting facilities such as fire protection, pipelines, cables, etc., please fully consider the operating space of the industrial overhead door or industrial roller shutter. (See the figure below)
Standard Improvement
Vertical Lift
Semi Vertical Lifting
Door In Door
Features of Industrial Lifting Doors (Sliding Doors)
1. Applicability: According to the architectural structure design, lifting doors such as industrial overhead doors and industrial roller shutters open vertically upwards and are hung flat on the inner side of the wall above the lift slide door opening, without occupying any indoor space; Fully utilize the advantage of vertical ascent without occupying both sides of the doorway, and maximize the release of doorway space;
2. Easy to operate: Multiple control methods, manual operation in a balanced state are fast and convenient;
3. Appearance: Double layer galvanized steel plate with polyurethane layer, surface embossed design can make the panel of the industrial roller shutter durable, easy to clean, beautiful and elegant, and enhance the corporate image;
4. Thermal insulation performance: Double layer steel plate reduces heat loss, with high-density polyurethane insulation layer sandwiched inside, providing excellent thermal insulation effect;
5. Noise isolation: Low noise opening, galvanized pulley seat equipped with adjustable ball bearings and wear-resistant rubber wheels to ensure silent opening and closing of the lift slide door.
6. Wind resistance: When the body of the industrial roller shutter reaches a certain width, external reinforcement ribs are designed to ensure its strength. Tested according to European standards, it can withstand instantaneous wind force of level 10.
7. Airtightness: The top, bottom, and both sides of the panel of industrial roller doors are equipped with high-quality rubber sealing strips, and there is also a reliable seal between the panels to ensure that the lifting garage door body is not corroded. Sealing strips are installed around the perimeter for excellent airtightness;
8. Safety devices: anti fall device, safety airbag (optional), prevent the industrial overhead door from falling or colliding with obstacles at the bottom of the door, and the lift slide door will automatically stop or run in reverse to avoid accidents; Anti wire rope breakage device and torsion spring breakage safety device. Prevent any form of lifting door damage to people or objects.
Product Picture of Industrial Lifting Door (Lift Slide Door)
Control Method of Industrial Lifting Door (Sliding Door)
The standard control method is to use three control buttons on the control box to control the opening, stopping, and closing of the lifting garage door. According to customer needs, multiple control methods can be implemented on the basis of electric industrial overhead doors.
1. Button style control
Control button switches can be added on the outside of industrial overhead doors to control their movement on both sides.
2. Pull rope switch control
Install a rope switch on the wall so that operators can operate the industrial overhead doors without leaving the vehicle.
3. Remote control
Flexible wireless controls such as "one-to-one", "many to one", and "one to many" can be achieved through a remote control.
4. Geomagnetic control
Because the geomagnetic ring only works on metal objects (such as vehicles, trays, etc.), this can avoid mixing of people and greatly extend the service life of the gate.
5. Optoelectronic control
Install a photoelectric switch on the outside of industrial shutter doors. When the light beam is blocked, the door can be opened and automatically closed through other devices such as automatic delay function. This device can also be used as a safety function.
6. Radar control
The device automatically sends a door opening signal when it detects moving objects (such as vehicles, personnel, etc.) under the lift slide door, achieving the opening of the rise garage door. Close the industrial roller shutter through other automatic devices.
7. Remote control
Communication devices such as mobile phones can be used to control the industrial roller shutter.
Specifications of Industrial Lifting Door
Component Name |
| Explain | Notes |
Industrial lift slide door operating environment |
| |
|
Service life of industrial lift slide door |
| |
|
Sliding speed of industrial lift slide door |
| |
|
door plank |
| Both the upper and lower parts are made of high-quality galvanized steel plates, and the interior is filled with rigid foam polyurethane door panels, which are environmentally friendly door panels; Thickness 40mm; The production of door panels is done on an assembly line and continuously, with high filling density, durability, insulation, good appearance color effect, and high strength. Wind pressure resistance parameters: standard wind pressure 450N/㎡ (wind resistant ribs can be added) The surface coating thickness of the color steel plate is 25-30 microns, and the door panel surface is sprayed with seven layers of paint, effectively ensuring the beauty and corrosion resistance of the product. Please refer to the product technical manual for details. The standard color for the inside and outside is white gray. The foam density of the door panel is 48Kg/m3 ± 2 Kg/m3, and the foam material is fluorine free polyurethane, a Japanese imported brand. The U-value test indicator is 0.84W/m2 º C. The U value between the door panels is 0.4 W/m2 º C, and the door panels do not support combustion, with a wind resistance of 450N/m2, equivalent to a level 10 typhoon. To assemble folding and other accessories, galvanized steel strip with a thickness of not less than 2mm must be added to the door panel. The door has good thermal insulation performance. The connection of the door panel is equipped with a sealing gasket to block the heat transfer and reduce heat loss. Airtightness: The air tightness of the installed overhead roller door is approximately 2.5m3/m2/h (under a pressure of 50 Pa). Wind resistance: 480N/m2; Equivalent to being able to withstand winds of level 10. Door panel edge sealing profile: The surface of the edge sealing profile of the door panel is completely sprayed with paint Balance system: The lifting doors are balanced by a high-strength spring system, and the minimum service life of the spring is 30000 cycles. All spring surfaces have undergone heat treatment for better corrosion resistance.
|
|
Density of foam material for door panels |
| |
|
electrical machinery | Renowned brand "Pioneer", specialized motor for industrial lifting doors | Each motor is equipped with a control box with three key switches for on, off, and stop. Specialized motor for industrial heavy duty lift doors, with stable performance and superior quality. Standard warranty period of 1 year Control power supply: 380V/50HZ
|
|
torsional spring |
| Accurate configuration calculation: The high-strength external torsion spring balance system uses precise and professional calculation formulas to accurately configure the torsion spring according to the size, weight, and sliding method of the door body, ensuring that the lift slide door can move up and down easily. The material of the torsion spring is 82b, which has undergone advanced heat treatment. Each spring is equipped with a spring anti breakage device, and in the event of any spring breakage, the industrial roller shutter will stop within 20cm.
|
|
Twisted spring shaft | |
|
Twisted spring bracket | |
|
wirerope | |
|
reel | |
|
track | The guide rail is made of Baosteel 2mm thick galvanized steel plate, with a galvanized layer of not less than 280g/m2. The connecting piece between the wheel rail and the wall rail is riveted, which will not damage the galvanized layer of the track. Standard: Industrial grade.
|
|
hinge | Adopting 2.5mm thick steel plate, optional universal type, standard: Industrial grade, with a unique, beautiful and elegant appearance. Excellent selection, high strength, good anti-corrosion and rust prevention effects: Especially the hinge is selected with a rare universal type in China without serial number, ensuring smooth operation of the roller in the guide rail.
|
|
roller | |
|
Performance of rail sliding system | After debugging, it runs smoothly and steadily without any sudden jumps or blockages, with a noise level of ≤ 60dB. Unique technology triangular adjustable pulley bracket ensures smooth operation of the pulley.
|
|
Bottom sealing strip | At the bottom, there is a sealing strip made of PVC material that is resistant to low temperatures and fractures. It is installed in an embedded manner with good sealing effect. Sealed around to ensure rain, dust, sound insulation, heat insulation and other performance,
|
|
Side sealing strip | There are sealing strips on the top, bottom, and sides, made of PVC material that is resistant to low temperatures and fractures. It is installed in an embedded manner with good sealing effect.
|
|
Strengthen the protective plate of the track | |
|
safety performance |
| Safety detection for operation under heavy duty lift doors: The air sensing safety edge ensures that when encountering resistance or obstacles, the lift slide door control system automatically rebounds the overhead roller door to prevent people, vehicles, and accidents from getting stuck. The safety protection devices are: 1. Equipped with bottom airbags, 2. Spring anti breakage device, 3. Control system with obstacle function display device.
|
|
window | | Optional |
Principle of Industrial Lifting Doors |
| The lift slide door adopts precise balance, and the weight of the door panel is completely balanced by the spring. In manual mode, industrial overhead doors can be easily opened completely, and the force used should not exceed 150N. The principle of implementation is to adjust the diameter of the door wire wheel and configure different types of torsion springs according to the size and installation method of the lift slide door during production. When the lift slide door is running at any height, the torque x diameter=torque, which remains constant. Therefore, the motor only plays a driving role in the operation of the lift slide door, effectively extending the service life of the motor. The power of the motor is very small, which has the effect of environmental protection and energy saving. The practical life of the spring can reach more than 30000 cycles. |
|
Industrial Lifting Door Motor & Torsion Spring
electrical machinery
| 
| power supply | 380-220（+6-10％） |
| electrical machinery | 3-phase 1400rpm |
| Maximum absorbed power (W) | 350 |
| Absorption current (A) | 2.0 |
| Initial capacitance (∪F) | 20 |
| Rotating thermal protection (℃) | 140 |
| Rotating speed of power output device (rpm) | 23 |
| Rated torque rejection of power output device (Nm) | 60 |
| Maximum speed of power output device | 24 |
| Renowned brand (Pioneer) industrial overhead roller door specific motor, with superior performance and stable quality. |
torsional spring
| 
| 
|
Other Hardware Components and Sealing Strips Within Industrial Overhead Doors
| Wire rope anti breakage device | Twisted spring anti breakage device |
 | Equipped with a torsion spring anti breakage device, once the torsion spring breaks, this device can clamp the door shaft, preventing heavy duty lift doors from falling within 20CM, ensuring the safety of personnel and goods. |
| The top sealing strip for industrial heavy duty lift doors, after installation, will tightly adhere to the wall when the door is closed, effectively maintaining the sealing of the top of the lift slide door. |
| Sealing strip at the top of the door | Sealing strip at the bottom of the door |
 |  |
| The top sealing strip for industrial heavy duty lift doors, after installation, will tightly adhere to the wall when the door is closed, effectively maintaining the sealing of the top of the lift slide door. | The bottom sealing strip for industrial heavy duty lift doors is in full contact with the ground, with good air tightness, effectively maintaining the sealing of the bottom of the door body. |
| Airbag device | Door side sealing strip |
 |  |
| Made of high-strength galvanized sheet profiles, it is beautiful and durable. | The side sealing strip is installed on the fixed angle plate of the track. After installation, it is tightly attached to the door panel, effectively maintaining the sealing of the side of the door body. |
| Loose leaf (hinge) | Pulley seat |
 |  |
| Made of high-strength galvanized sheet profiles, it is beautiful and durable. | Pulley seat: made of high-quality galvanized sheet material, with strong adjustability, corrosion resistance, and beautiful appearance. |
English
Español
русский
tiếng việt
